If you have a chainsaw that has a tension screw, it’s time to replace it. The tension screw is a small metal screw on the side of the chainsaw that holds the chain in place. Over time, the screw can become stripped or lose its grip on the chain, which will cause the chain to slip and potentially damage your saw.
Depending on the type of chainsaw, the replacement procedure will be different. Some chainsaws require you to use a special tool, while others use a Phillips head screwdriver.
Table of Contents
How Do You Properly Replace The Tension Screw On A Chainsaw
Replacing the tension screw on a chainsaw is a relatively straightforward task, but it is still important to take detailed care.
The tension screw helps to keep the chain in place and tight against the guide bar. Here are the steps you need to follow to replace the tension screw on a chainsaw:
- Disconnect the spark plug lead from the spark plug and remove the plug so that the chainsaw cannot accidentally start up while you are working on it.
- Status fastened in the chainsaw’s storage compartment with two screws. Be careful not to remove these screws completely, as they will need to be re-tightened later.
- Remove the cover of the chainsaw and set it aside.
- Locate the tension latch at the top of the chainsaw and remove it by turning it counterclockwise with a wrench or pliers.
Where is the tensioning screw on a chainsaw?
Chainsaw tensioning screws come in a few different varieties, but they all perform the same function. The screw tightens or loosens the chain around the bar, which affects the tension on the chain.
Screws are often positioned on the side of the chainsaw near the handle, while others are located towards the back of the chainsaw.
The position of the screws may vary depending on the model and brand of chainsaw. It is important to know where this screw is located so that you can properly tension your chain.
Why won’t my chainsaw chain tighten?
If your chainsaw chain won’t tighten, there are a few possible causes. You may not have the correct tension on the chain, the chain may be too loose, or the bar may be too tight.
If the chain is too loose, you can try to tighten it by adjusting the tension screw on the side of the chainsaw. If that doesn’t work, you may need to replace the chain.
If the bar is too tight, you can try to loosen it by adjusting the screws on either side of the bar. You may need to replace the bar if that doesn’t work.
Why does my chainsaw keep throwing the chain?
A frequent problem with chainsaws is that the chain will become unattached and may fly off. This can be very dangerous, as the instrument can easily become a projectile and cause serious damage.
There are several reasons why a chainsaw might throw the chain, and it is important to troubleshoot the problem in order to prevent injuries.
The most common reason a chainsaw throws the chain is that the bar oil has been depleted.
When this happens, the chain will start to grind against the bar, and eventually, it will fly off. To prevent this from happening, be sure to keep your bar oil levels topped off.
Another common reason for a chainsaw throwing its chain is because of a dull blade. When the blade becomes dull, it will start to heat up and eventually warp.
How much tension should be on a chainsaw chain?
A chainsaw is a great tool to have around the house, but it’s important to make sure that you’re using it safely. One of the most important things to remember is how much tension should be on a chainsaw chain.
If your chain is loose enough to pass through the hooks of the bar, it can fall off; if it is too tight, it can loosen the chain and keep it from falling. When setting the chain, refer to your owner’s manual for a proper setting.
Most chainsaws require between 2 and 3 pounds of tension, but be sure to check your specific model. You can also try experimenting with different levels of tension until you find what works best for you.
Remember to keep an eye on your chain tension while you’re using the chainsaw, and always adjust it according to your owner’s manual.
How tight should my chain be on my chainsaw?
When it comes to chainsaw chain tension, there is a lot of debate on how tight is too tight. Some people say that you should only tighten the chain until it just touches the bar, while others say that you should crank it down as tight as possible.
It isn’t appropriate to say there is a single right or wrong answer to this question. It depends on your own point of view and the user.
If your chainsaw feels like it’s laboring or if the chain keeps coming off, then you may need to loosen the chain a bit.
Excessive tension can damage the saw and shorten the lifespan of the machine. Conversely, if the saw is loose, it can cause damage to the saw and also create tension.
It’s important to find a happy medium – not too tight and not too loose – so that your chainsaw runs smoothly and efficiently.
Can you over-tighten a chainsaw chain?
It’s easy to think that more is always better, but when it comes to tightening the chain on your chainsaw, over-tightening can do more harm than good.
In fact, if you tighten the chain too much, you can actually damage the saw and make it difficult to use.
The key to tightening a chainsaw chain is finding the right balance. You want to make sure that the chain is tight enough so that it doesn’t come loose while you’re using it, but you don’t want to tighten it so much that it becomes difficult to move.
If you’re not sure how tight the chain should be, ask a professional for help. Difficulties in adjusting their mind are incorporated into their knowledge of what is too tight and what is too loose.